This tut was written for those with a basic knowledge of psp.
I am using the awesome artwork of Ismael Rac.
You need a license to use this art work. Please do not use without a license.
You can find this art at his Store HERE
Supplies Needed
I used PSPX...but any of them should work.
Filters used
Unplugged Tools-Interlace
Unplugged Tools-Interlace
Font of Choice, I used Clive Barker
Drop Shadow usually V2 H2 50 black
Let's get started
*Remember to add your drop shadow as you go along*
And as I usually go to Image, canvas size 800 x 800.
Add a new raster layer, paste paper 3, apply your mask, merge group and delete.
Paste the large frame, free rotate to the left at 5 degrees, click inside with your magic wand, expand by 5, paste paper 8 or one you prefer, invert, delete.
Do not deselect yet, paste your close up tube and move to the left a bit, delete, select none. Duplicate your tube, go to Adjust, blur, Gaussian blur at 5%, change the blend mode to screen or one you like, merge down.
Duplicate your frame, resize to 55%, mirror and move down on the right side, click inside with your magic wand, expand by 5 and paste paper 8, invert, delete.
Mirror your tube, then paste the belt buckle part in the small frame, delete, select none.
Duplicate, Adjust, blur, Gaussian blur at 5%, change the blend mode to screen, merge down, select none.
Apply Unplugged Tools-Interlace with these settings
12, 40, 1, 0
Also apply this same filter to the paper on the large frame.
Paste the lights and move to the top of the large frame, free rotate to the left at 5 degrees.
Paste the light beam and place on one side, duplicate and mirror and place on the other side.
Resize your tube to 43%, if using the same one I am and paste off center a bit.
If you want the light beams on your tube layer, then move your tube down under the light layer.
Paste the wire star above the mask layer on the lower right side, duplicate, flip and mirror, adjust how you want it.
Paste wire 2 on the upper right side, move out a bit, duplicate, mirror, flip and adjust.
Paste the splatter on the upper right side above the wire layer, duplicate, mirror, flip.
Paste the film strip at the bottom, above the large frame layer, click inside each square and expand by 3, paste paper 11, invert, delete, make sure the paper layer is below the film strip.
Resize the stool to 50%, place on the left side above the film strip layer.
Resize the microphone to 30%, free rotate to the right at 90 and place on the stool.
Resize the guitar to 85%, free rotate to the right at 10 degrees and place by the stool.
Resize the pills to 15% and place on the base of the stool at the bottom.
Resize the CD to 30%, duplicate 2 or 3 times more and place them below the small frame paper layer in different areas.
Paste the chain below the tube layer at the bottom.
Resize the lips to 40%, free rotate to the left at 15 and place on the upper right side.
Resize the music notes to 30%, rotate one or two at 15 degree, duplicate and place where you like them.
Paste the Disco Ball above the wire layers on the upper left side.
Add any other elements you would like.
Crop your tag to be sure no stray shadows are on the edges of your tag.
And as I usually go to Image, canvas size 800 x 800.
Add a new raster layer, paste paper 3, apply your mask, merge group and delete.
Paste the large frame, free rotate to the left at 5 degrees, click inside with your magic wand, expand by 5, paste paper 8 or one you prefer, invert, delete.
Do not deselect yet, paste your close up tube and move to the left a bit, delete, select none. Duplicate your tube, go to Adjust, blur, Gaussian blur at 5%, change the blend mode to screen or one you like, merge down.
Duplicate your frame, resize to 55%, mirror and move down on the right side, click inside with your magic wand, expand by 5 and paste paper 8, invert, delete.
Mirror your tube, then paste the belt buckle part in the small frame, delete, select none.
Duplicate, Adjust, blur, Gaussian blur at 5%, change the blend mode to screen, merge down, select none.
Apply Unplugged Tools-Interlace with these settings
12, 40, 1, 0
Also apply this same filter to the paper on the large frame.
Paste the lights and move to the top of the large frame, free rotate to the left at 5 degrees.
Paste the light beam and place on one side, duplicate and mirror and place on the other side.
Resize your tube to 43%, if using the same one I am and paste off center a bit.
If you want the light beams on your tube layer, then move your tube down under the light layer.
Paste the wire star above the mask layer on the lower right side, duplicate, flip and mirror, adjust how you want it.
Paste wire 2 on the upper right side, move out a bit, duplicate, mirror, flip and adjust.
Paste the splatter on the upper right side above the wire layer, duplicate, mirror, flip.
Paste the film strip at the bottom, above the large frame layer, click inside each square and expand by 3, paste paper 11, invert, delete, make sure the paper layer is below the film strip.
Resize the stool to 50%, place on the left side above the film strip layer.
Resize the microphone to 30%, free rotate to the right at 90 and place on the stool.
Resize the guitar to 85%, free rotate to the right at 10 degrees and place by the stool.
Resize the pills to 15% and place on the base of the stool at the bottom.
Resize the CD to 30%, duplicate 2 or 3 times more and place them below the small frame paper layer in different areas.
Paste the chain below the tube layer at the bottom.
Resize the lips to 40%, free rotate to the left at 15 and place on the upper right side.
Resize the music notes to 30%, rotate one or two at 15 degree, duplicate and place where you like them.
Paste the Disco Ball above the wire layers on the upper left side.
Add any other elements you would like.
Crop your tag to be sure no stray shadows are on the edges of your tag.
Once happy with it all, close off any backgrounds, merge visible.
Resize first, then add your copyrights and name.
Resize first, then add your copyrights and name.
That's it
Hope you enjoyed doing my tut.
No comments:
Post a Comment