Ready for Speed

This tut was written for those with a basic knowledge of psp.

I am using the awesome artwork of  Ted Hammond.

I am using two tubes. I bought mind when CILM was still around, but they have since closed and you can find his art at CDO now.

You need a license to use this art work. Please do not use without a license.
 

 You can find this art at CDO Store  HERE

 

Supplies Needed

I used PSPX...but any of them should work.
 Scrap Need for Speed by Toxic Desirez  HERE
Scroll down until you see the kit name
Check out the rest of the blog HERE
Monti's Blind Mask 1  HERE
Click on Extras to find the mask
Filters
EyeCandy4000-Bevel Boss
Screen Works-Lace Screen

Font of Choice, I used Checker Hat

Drop Shadow usually V2 H2 50 black
Drop shadow on this one I used V-2 H-2 Blur 15
Use whatever drop shadow you prefer
 

 *Remember to add your drop shadow as you go along*

Open a new image 800 x 800 or one you prefer.
Paste the wire and once you draw your circle, take your pick tool and make the wire a bit larger.
Click on your preset tool and select the circle one, set the width to 40, draw a circle over the wire, convert to raster layer.
Apply EyeCandy4000-Bevel Boss with these settings or play around and get one you prefer
Bevel width 5.76
Bevel Height 50,  Smoothness75,  0
Lighting
68, 73
100, 25
Highlight color white, Shadow color black
Bevel Profile
Button
Click inside with your magic wand, expand by 5, new raster layer, fill with white, apply the filter Screen Works-Lace Screen.
Paste the double flags and move toward the top more.

Paste the film strip and resize to 90%, move toward the bottom more, click inside with your magic wand, expand by 3, paste paper of choice, I used #11 and
then go to Adjust
Hue and Saturation, colorize with both numbers on 0.

Paste tire tracks 1, free rotate to the right at 45 degrees, move under the car tires,
get your Pick tool, hold down the shift key and being on the top corner square, pull down as far as you want it to be, then go to the other corner at the top and do the same until the tracks are straight under the car tires. Then pull each end out to make it a bit longer.

Paste the stop light above the filmstrip, resize to 90%, change the color of the lights to those of a regular street light colors, green, yellow and red or
if you like these colors then leave them as it.

Resize the speed sign to 50%, change the color like before with the car or leave as is and paste on the stop light post.

Paste car 2 below the double flags in the circle, resize to 50%, change the color like before, duplicate, mirror.

Being on the top layer now, paste your tube with the rim on the right side, and your other tube on the left side below the car layer.

Resize the tire iron to 30%, place by the tube on the right.
Resize the wrench to 25%, free rotate to the left at 90 degrees.
Resize the rim to 45%, place behind the tube on the left, duplicate and move over and up a bit, change the color like before.
Resize the pit pass to 20%, place on the left on the film strip and erase a little bit of the chain to make it look like it is hanging on there.
Resize the dragonfly to 35%, place at the top where you like.
Resize the sunglasses to 25%, change the color, paste on the left by the car.

Add a new raster layer, fill with black, apply your mask, move to the bottom layer and resize larger if needed.

 Add any other elements you would like, make it your own.

Crop your tag to be sure no stray shadows are on the edges of your tag.

Once happy with it all, close off any backgrounds, merge visible.
Resize first, then add your copyrights and name.
 

That's it

Hope you enjoyed doing my tut.